Component selection guide

What to send after a loop leak when only some liquid-cooling parts will be replaced

A checklist for a partial replacement quote after a leak: what failed, what stays, and how the new parts must connect, without treating a second source as a guaranteed mate.

Loop leakPartial replaceWhat to send
On this page

After a liquid-cooling loop leak, you may not replace the whole loop. A useful request still has to say which parts will be changed, which parts will stay in place, and how the new pieces must connect to what remains. This page is a checklist for a partial replacement quote. It does not certify that a second source will mate, and it is not a stock or lead-time list. YOCOOLING coordinates quotations for specified liquid-cooling components from China.

This is not a rewrite of the existing Multi-product Quote Request guide, which covers how to organize a mixed parts list, or of the leak, flow and pressure-test questions, which cover how to ask for test information. Use those pages for the broader list or the test language. Use this page when the immediate job is: a leak happened, only some parts will be replaced, and a quote has to be comparable.

Record what leaked, and what will stay

State where the leak was observed — for example at a quick-disconnect joint, a hose end, a manifold port, a cold-plate fitting, a valve, or a sensor boss — and what you can see without taking the whole loop apart. Then list, as clearly as you can, the parts you intend to replace and the parts you intend to reuse. A request that only says “loop leaked, send replacement parts” leaves the supplier guessing which half of a coupling, which hose length, or which seal is actually needed.

If the system was drained, isolated, or already partly disassembled, say what was removed. If fluid is still in the loop, say so, and do not ask a quotation to assume a dry inspection that has not happened.

Identify the remaining interface, not just the failed piece

A partial replacement has to connect to hardware that will stay installed. That remaining interface is often more important than a generic description of the failed part. Record:

  • The exact part number, series, colour code, valve type (valved or non-valved), and any revision mark on both the part being replaced and the mating half that will stay, if a quick disconnect is involved.
  • End connections, thread or coupling standard, seal type, and hose inside diameter, length and orientation for hose or tube assemblies.
  • Port size, pattern and any remaining fitting on a manifold, cold plate or valve body that will not be changed.

If a label is readable, photograph it. If it is not, photograph the end view and the installed orientation and say that the marking is unreadable. For an installed UQD half, follow the existing label and photo identification guide rather than repeating that whole checklist here. Series-level UQD fields are in the QD & UQD Selection guide. Hose and tube fields are in the hose and tube Quote Request Checklist.

Do not treat a similar-looking part as a guaranteed mate

A second-source coupling, hose end or fitting can look similar and still not mate, seal, or carry the same valve state as the half that remains in the rack. This page does not claim that parts from different brands are interchangeable, certified together, or safe to mix because they share a nominal size or a “UQD” description. If you are willing to consider a substitute, say which fields must stay exact (for example the interface standard and revision, valved or non-valved, end thread, or material) and which fields you can review.

If the remaining half is still installed, include that brand and part number in the request even when you plan to buy only the failed half. A quote that ignores the installed counterpart cannot be compared honestly.

Coolant, conditions and what you want cleaned or tested

If you know the coolant type, concentration, and the operating temperature or pressure at the leak location, include them. If you do not know, say so; do not invent a fluid. State whether the replacement parts must be cleaned, capped, or supplied with a specified test record. Questions about how to ask for leak, flow or pressure-test information belong in the test-questions guide. This page only asks you to say whether those records are required for the parts you are replacing, so the quotation can include or exclude them.

Material and seal compatibility still matters for any part that will see the same coolant as the rest of the loop. The coolant and wetted-materials questions remain the place to list those fields. In a partial replacement, also say which wetted parts are being reused, so a substitute is not proposed in isolation from the seals and metals that will stay.

What to send with the request

  • Where the leak was seen, and whether the loop has been drained or partly disassembled.
  • A list of parts to be replaced, and a list of parts that will stay in place, including remaining mating halves.
  • Exact part numbers, revisions, colour codes and valved/non-valved state where they are visible.
  • Label photos, an end-view photo, and an installed-orientation photo; note it if a label cannot be read.
  • End connections, thread or coupling standards, hose size and length, and port details on any reused manifold, plate or valve.
  • Coolant type and concentration if known, plus temperature or pressure at the leak location if known.
  • Quantity, required condition, and whether cleaning, capping or a stated test record should be included in the quote.
  • Whether a substitute may be offered, and which interface or material fields must stay exact.

Send that package from Contact or Request a Quote. If the replacement is a UQD half, you can also start from the UQD category. If several line items are involved, attach the list and use the Multi-product Quote Request guide so each remaining interface stays attached to the line it belongs to. You do not need a product page for every line.

Page drafted 18 November 2026. It is a request checklist, not a certification of interchange, a stock list, or a repair procedure.

When the remaining connection is a named official coupling or hose code, specification examples already on this site — not a stock list — include CEJN LQC 10 153 1290 / 10 153 6290 and CEJN peroxide-cured EPDM hose. For a longer connection-detail checklist on the plate side, see Cold-plate-side connection details that belong in a replacement quote.