Component selection guide

Identifying an installed UQD half from a label or photo — without assuming a second source will mate

How to read a label and photograph an installed UQD half so a replacement quote can be compared, without treating a second source as a guaranteed mating part.

LabelPhotoInstalled view
On this page

If you are replacing one half of a universal quick disconnect already in a loop, the first job is to identify the installed half. That is a narrower task than choosing a new pair for a clean design.

The existing QD and UQD selection guide covers series-level fields, coolant, pressure, flow, and documentation for a selection request. This page adds the evidence you can collect from a label or from photographs when the other half, or a second source, has not yet been confirmed. A similar outline, colour, or size is not enough to treat another manufacturer’s part as a mating half or as a certified substitute.

What on the label is actually useful

If the coupling still has a readable manufacturer label or body marking, copy it in full. The fields that most often matter are:

  • Manufacturer name and the complete part number, not a shortened series nickname.
  • Series or size designation, such as UQD02, UQD04, UQD06, or UQD08, exactly as printed.
  • Whether the half is a socket or a plug.
  • Whether it is valved or non-valved, if that is marked.
  • Colour code or housing colour, together with what the colour is intended to show, if the label says so. Colour by itself is not a part number.
  • End connection: thread, flange, panel mount, or hose termination, including any size or standard marked on the part.
  • Revision, issue, or specification mark, if present.
  • Material or seal mark, if present.

If a field is worn off, write that it is unreadable instead of filling it in from memory or from a catalogue photograph.

Photographs that help a quote

Three views are usually more useful than a single wide shot of the rack:

  1. The label, square-on and in focus, with any second line or data-matrix code included.
  2. An end view of the mating face (and, if it can be taken safely, of the end connection). This is how socket versus plug, and the face geometry, can be checked later.
  3. The installed orientation: which way the half points, how much envelope is left around it, and what it is connected to (hose, manifold, cold plate, or panel). Include a short note if the half is in a tight space or can only be disconnected in one direction.

Do not disconnect a live loop just to take a photograph. If the face cannot be seen without releasing pressure, say so, and send the label and installed views you can take safely.

A ruler or a known reference in the frame can help with end-connection size, but it does not replace the thread or termination mark.

If the label cannot be read

When the marking is gone, the request can still start from:

  • The equipment or manifold model, if you have it.
  • The opposite half, if that half is still labelled and you know it is the original mating part — and you should say that this is an inference, not a measurement of the worn half.
  • Any previous purchase order, drawing, or spare-part list.
  • The three photographs above, plus a clear statement that the installed part number is unknown.

It is better to mark the part number as unknown than to quote a look-alike series from a catalogue.

Do not assume a second source will mate

UQD is an open interface specification. That does not mean that every part sold under a UQD-like name will mate, seal, or perform the same way in your loop, or that a second manufacturer has certified the pair you have in mind.

Before you treat another brand as a replacement:

  • Confirm the interface designation and the revision of both halves, not only the size name.
  • Confirm socket versus plug, valved versus non-valved, and the end connection.
  • Do not take a similar colour, hex size, or hose barb as proof of interchangeability.
  • If the original pair was qualified as a set, say that you need the qualification basis kept, or that you are prepared to evaluate a different pairing.

The official OCP Universal Quick Disconnect (UQD) Specification v2.0.0 (Version 2.0.0; effective 22 September 2026) states in section 6.1 that the v2 design is intended to be backwards compatible with the earlier, separate UQD and UQDB v1 specifications, and that end users are encouraged to carry out a deployment evaluation. Appendix 15.1 lists mixing risks, including differences in chamfer and sealing, length and outside diameter, flow coefficient and pressure drop, and valve travel and engagement.

Those clauses are about the written specification. They are not a certificate for a particular mixed pair, and they are not a shipping announcement for any manufacturer’s v2 product line. A specification effective date is not the same thing as a vendor ship date. If you are mixing revisions or sources, the evaluation still belongs to the end user and to the documentation you require in the quote.

How to send the request

A replacement request for an installed UQD half should include:

  • Label text, or a statement that the label is unreadable.
  • The photographs listed above.
  • Socket or plug, valved or non-valved, series or size, revision, and end connection, to the extent they are known.
  • Coolant, pressure, temperature, and any leakage or cleanliness requirement you already have — or a pointer that these will follow, so they are not invented in the first message.
  • Whether a second source may be quoted at all, and whether it must be evaluated before it is treated as a mating half.

You can send that package from the UQD category or with a longer list through the Multi-product Quote Request guide. For series-level selection fields, use the QD and UQD selection guide. Availability, price, lead time, and any certification belong in the quotation, not in this identification step.

Sources and update date

Page drafted 17 November 2026. The OCP specification cited above was read from the official PDF. This page is not a stock list, a cross-brand approval, or a claim that any two UQD halves will mate.

You can send the photos and part details from Contact or Request a Quote.

Related reading

If only some parts of a loop will be replaced after a leak, see What to send after a loop leak when only some liquid-cooling parts will be replaced.

Named UQD examples already on this site, useful when you are comparing an official part number — not as a stock list — include FITOK S4-UQD02-ST7-D-BL, FITOK S4-UQD08-MP10-B-BL, and CEJN 10 153 1026 / 10 153 6676.